Arduino-compatible IDE with ESP8266 support
This project brings support for ESP8266 chip to the Arduino environment. ESP8266WiFi library bundled with this project has the same interface as the WiFi Shield library, making it easy to re-use existing code and libraries.
Installing with Boards Manager
Starting with 1.6.4, Arduino allows installation of third-party platform packages using Boards Manager. We have packages available for Windows, Mac OS, and Linux (32 and 64 bit).
- Install Arduino 1.6.4 from the Arduino website.
- Start Arduino and open Perferences window.
http://arduino.esp8266.com/package_esp8266com_index.jsoninto Additional Board Manager URLs field. You can add multiple URLs, separating them with commas.
- Open Boards Manager from Tools > Board menu and install esp8266 platform (and don't forget to select your ESP8266 board from Tools > Board menu after installation).
Building latest version from source
$ git clone https://github.com/esp8266/Arduino.git $ cd Arduino/build $ ant dist
- Generic esp8266 modules (without auto-reset support)
- Olimex MOD-WIFI-ESP8266
Things that work
Basic Wiring functions
analogWrite work as usual.
Pin numbers correspond directly to the esp8266 GPIO pin numbers. To read GPIO2,
GPIO0-GPIO15 can be
GPIO16 can be
analogRead(A0) reads the value of the ADC channel connected to the TOUT pin.
analogWrite(pin, value) enables software PWM on the given pin. PWM may be used on pins 0 to 15.
analogWrite(pin, 0) to disable PWM on the pin.
value may be in range from 0 to
PWMRANGE, which is currently equal to 1023.
Pin interrupts are supported through
Interrupts may be attached to any GPIO pin, except GPIO16. Standard Arduino interrupt
types are supported:
The most usable pin functions are mapped to the macro
SPECIAL, so calling
will switch that pin in the most usable FUNCTION_X. Those are UART RX/TX on pins 1 - 3, HSPI for pins 12-15 and CLK functions for pins 0, 4 and 5.
Timing and delays
micros return the number of milliseconds and microseconds elapsed after reset, respectively.
delay pauses the sketch for a given number of milliseconds and allows WiFi and TCP/IP tasks to run.
delayMicroseconds pauses for a given number of microseconds.
Remember that there is a lot of code that needs to run on the chip besides the sketch
when WiFi is connected. WiFi and TCP/IP libraries get a chance to handle any pending
events each time the
loop() function completes, OR when
delay(...) is called.
If you have a loop somewhere in your sketch that takes a lot of time (>50ms) without
delay(), you might consider adding a call to delay function to keep the WiFi
stack running smoothly.
There is also a
yield() function which is equivalent to
delay(0). The delayMicroseconds
function, on the other hand, does not yield to other tasks, so using it for delays
more than 20 milliseconds is not recommended.
Serial object works much the same way as on a regular Arduino. Apart from hardware FIFO (128 bytes for TX and RX) HardwareSerial has additional 256-byte TX and RX buffers. Both transmit and receive is interrupt-driven. Write and read functions only block the sketch execution when the respective FIFO/buffers are full/empty.
Serial uses UART0, which is mapped to pins GPIO1 (TX) and GPIO3 (RX). Serial may be remapped to GPIO15 (TX) and GPIO13 (RX) by calling
swap again maps UART0 back to GPIO1 and GPIO3.
Serial1 uses UART1 which is a transmit-only UART. UART1 TX pin is GPIO2. To use
By default the diagnostic output from WiFi libraries is disabled when you call
Serial.begin. To enable debug output again, call
Serial.setDebugOutput(true);. To redirect debug output to
Serial1 instead, call
You also need to use
Serial.setDebugOutput(true) to enable output from the Arduino
Serial1 objects support 5, 6, 7, 8 data bits, odd (O), even (E), and no (N) parity, and 1 or 2 stop bits. To set the desired mode, call
Serial.begin(baudrate, SERIAL_6E2);, etc.
The Program memory features work much the same way as on a regular Arduino; placing read only data and strings in read only memory and freeing heap for your application.
The important difference is that on the esp8266 the literal strings are not pooled. This means that the same literal string defined inside a
PSTR("") will take up space for each instance in the code. So you will need to manage the duplicate strings yourself.
This is mostly similar to WiFi shield library. Differences include:
WiFi.mode(m): set mode to
WiFi.softAP(ssid)to set up an open network
WiFi.softAP(ssid, password)to set up a WPA2-PSK network (password should be at least 8 characters)
WiFi.macAddress(mac)is for STA,
WiFi.softAPmacAddress(mac)is for AP.
WiFi.localIP()is for STA,
WiFi.softAPIP()is for AP.
WiFi.printDiag(Serial);will print out some diagnostic info
WiFiUDPclass supports sending and receiving multicast packets on STA interface. When sending a multicast packet, replace
udp.beginPacketMulticast(addr, port, WiFi.localIP()). When listening to multicast packets, replace
udp.beginMulticast(WiFi.localIP(), multicast_ip_addr, port). You can use
udp.destinationIP()to tell whether the packet received was sent to the multicast or unicast address. Also note that multicast doesn't work on softAP interface.
WiFiServer, WiFiClient, and WiFiUDP behave mostly the same way as with WiFi shield library. Four samples are provided for this library. You can see more commands here: http://www.arduino.cc/en/Reference/WiFi
Library for calling functions repeatedly with a certain period. Two examples included.
It is currently not recommended to do blocking IO operations (network, serial, file) from Ticker callback functions. Instead, set a flag inside the ticker callback and check for that flag inside the loop function.
This is a bit different from standard EEPROM class. You need to call
before you start reading or writing, size being the number of bytes you want to use.
Size can be anywhere between 4 and 4096 bytes.
EEPROM.write does not write to flash immediately, instead you must call
whenever you wish to save changes to flash.
EEPROM.end() will also commit, and will
release the RAM copy of EEPROM contents.
EEPROM library uses one sector of flash located at 0x7b000 for storage.
Three examples included.
I2C (Wire library)
Wire library currently supports master mode up to approximately 450KHz.
Before using I2C, pins for SDA and SCL need to be set by calling
Wire.begin(int sda, int scl), i.e.
Wire.begin(0, 2); on ESP-01,
else they default to pins 4(SDA) and 5(SCL).
SPI library supports the entire Arduino SPI API including transactions, including setting phase (CPHA). Setting the Clock polarity (CPOL) is not supported, yet (SPI_MODE2 and SPI_MODE3 not working).
APIs related to deep sleep and watchdog timer are available in the
ESP object, only available in Alpha version.
ESP.deepSleep(microseconds, mode) will put the chip into deep sleep.
mode is one of
WAKE_RF_DISABLED. (GPIO16 needs to be tied to RST to wake from deepSleep.)
ESP.restart() restarts the CPU.
ESP.getFreeHeap() returns the free heap size.
ESP.getChipId() returns the ESP8266 chip ID as a 32-bit integer.
Several APIs may be used to get flash chip info:
ESP.getFlashChipId() returns the flash chip ID as a 32-bit integer.
ESP.getFlashChipSize() returns the flash chip size, in bytes, as seen by the SDK (may be less than actual size).
ESP.getFlashChipSpeed(void) returns the flash chip frequency, in Hz.
ESP.getCycleCount() returns the cpu instruction cycle count since start as an unsigned 32-bit. This is useful for accurate timing of very short actions like bit banging.
ESP.getVcc() may be used to measure supply voltage. ESP needs to reconfigure the ADC
at startup in order for this feature to be available. Add the following line to the top
of your sketch to use
TOUT pin has to be disconnected in this mode.
Note that by default ADC is configured to read from TOUT pin using
ESP.getVCC() is not available.
Library was adapted to work with ESP8266 by including register definitions into OneWire.h Note that if you already have OneWire library in your Arduino/libraries folder, it will be used instead of the one that comes with this package.
mDNS responder (ESP8266mDNS library)
Allows the sketch to respond to multicast DNS queries for domain names like "foo.local". Currently the library only works on STA interface, AP interface is not supported. See attached example and library README file for details.
DNS server (DNSServer library)
Implements a simple DNS server that can be used in both STA and AP modes. The DNS server currently supports only one domain (for all other domains it will reply with NXDOMAIN or custom status code). With it clients can open a web server running on ESP8266 using a domain name, not an IP address. See attached example for details.
This library exposes the ability to control RC (hobby) servo motors. It will support upto 24 servos on any available output pin. By defualt the first 12 servos will use Timer0 and currently this will not interfere with any other support. Servo counts above 12 will use Timer1 and features that use it will be effected. While many RC servo motors will accept the 3.3v IO data pin from a esp8266, most will not be able to run off 3.3v and will require another power source that matches their specifications. Make sure to connect the grounds between the esp8266 and the servo motor power supply.
Other libraries (not included with the IDE)
Libraries that don't rely on low-level access to AVR registers should work well. Here are a few libraries that were verified to work:
- arduinoWebSockets - WebSocket Server and Client compatible with esp8266 (RFC6455)
- aREST REST API handler library.
- Blynk - easy IoT framework for Makers (check out the Kickstarter page).
DHT11 - Download latest v1.1.0 library and no changes are necessary. Older versions should initialize DHT as follows:
DHT dht(DHTPIN, DHTTYPE, 15);
- NeoPixelBus - Arduino NeoPixel library compatible with esp8266.
- PubSubClient MQTT library by @Imroy.
- RTC - Arduino Library for Ds1307 & Ds3231 compatible with esp8266.
- Souliss, Smart Home - Framework for Smart Home based on Arduino, Android and openHAB.
Upload via serial port
Pick the correct serial port. You need to put ESP8266 into bootloader mode before uploading code.
For stable use of the ESP8266 a power supply with 3V3 and >= 250mA is required.
- using Power from USB to Serial is may unstable, they not deliver enough current.
There are many different USB to Serial adapters / boards.
- for full upload management you need RTS and DTR
- the chip need to have 3V3 TTL (5V may damage the chip)
- not all board have all pins of the ICs as breakout (check before order)
- CTS and DSR are not useful for upload (they are Inputs)
- may others (drop a comment)
Minimal hardware Setup for Bootloading and usage
|TX or GPIO2*||RX|
- GPIO15 is also named MTDO
- Reset is also named RSBT or REST (adding PullUp improves the stability of the Module)
- GPIO2 is alternative TX for the boot loader mode
esp to Serial
Minimal hardware Setup for Bootloading only
|TX or GPIO2||RX|
- if no RTS is used a manual power toggle is needed
Minimal hardware Setup for running only
Issues and support
Submit issues on Github: https://github.com/esp8266/Arduino/issues
License and credits
Arduino IDE is based on Wiring and Processing. It is developed and maintained by the Arduino team. The IDE is licensed under GPL, and the core libraries are licensed under LGPL.
This build includes an xtensa gcc toolchain, which is also under GPL.
Espressif SDK included in this build is under Espressif Public License.
Esptool written by Christian Klippel is licensed under GPLv2, currently maintained by Ivan Grokhotkov: https://github.com/igrr/esptool-ck.
ESP8266 core support, ESP8266WiFi, Ticker, ESP8266WebServer libraries were written by Ivan Grokhotkov, email@example.com.
SPI Flash File System (SPIFFS) written by Peter Andersson is used in this project. It is distributed under MIT license.