Infrared remote library for Arduino: send and receive infrared signals with multiple protocolsPort from Arduino-IRremote https://github.com/z3t0/Arduino-IRremote


Keywords
ir, remote
License
LGPL-2.1
Install
platformio lib install 8648

Documentation

IRremote Arduino Library

Available as Arduino library "IRremote"

Version 2.7.0

License: GPL v2 Installation instructions Join the chat at https://gitter.im/z3t0/Arduino-IRremote LibraryBuild

This library enables you to send and receive using infra-red signals on an Arduino.

Tutorials and more information will be made available on the official homepage.

Installation

Click on the LibraryManager badge above to see the instructions.

FAQ

  • IR does not work right when I use Neopixels (aka WS2811/WS2812/WS2812B) Whether you use the Adafruit Neopixel lib, or FastLED, interrupts get disabled on many lower end CPUs like the basic arduinos for longer than 50 us. In turn, this stops the IR interrupt handler from running when it needs to. There are some solutions to this on some processors, see this page from Marc MERLIN
  • The default IR timer on AVR's is timer 2. Since the Arduino Tone library as well as analogWrite() for pin 3 and pin 11 requires timer 2, this functionality cannot be used simultaneously.
  • You can use multiple IR receiver by just connecting the output pins of several IR receivers together. The IR receivers use an NPN transistor as output device with just a 30k resistor to VCC. This is almost "open collector" and allows connecting of several output pins to one Arduino input pin.

Supported IR Protocols

Aiwa, BoseWave, Denon, Dish, JVC, Lego, LG, MagiQuest, Mitsubishi, NEC, Panasonic, RC5, RC6, Samsung, Sanyo, Sharp, Sony, Whynter, (Pronto).
Protocols can be switched off and on by changing the lines in IRremote.h:

#define DECODE_<PROTOCOL_NAME>  1
#define SEND_<PROTOCOL_NAME>    1

Useful defines

You may modify the behavior of the library by changing this values in the source code or just defining a new value for compile (the latter is not possible with the Arduino IDE, so consider to use sloeber.

Name File Default value Description
DEBUG IRremote.h disabled Enables lots of lovely debug output.
USE_NEC_STANDARD IRremote.h disabled Use LSB first, address/code schema for encoding.
USE_NO_SEND_PWM IRremote.h disabled Use no carrier PWM, just simulate an active low receiver signal.
USE_SOFT_SEND_PWM IRremote.h disabled Use carrier PWM generation in software, instead of hardware PWM.
PULSE_CORRECTION_MICROS IRremote.h 3 If USE_SOFT_SEND_PWM, this amount is subtracted from the on-time of the pulses.
USE_SPIN_WAIT IRremote.h disabled If USE_SOFT_SEND_PWM, use spin wait instead of delayMicros().
RAW_BUFFER_LENGTH IRremoteint.h 101 Buffer size of raw input buffer. Must be odd!
IR_SEND_DUTY_CYCLE IRremoteBoardDefs.h 30 Duty cycle of IR send signal.
MICROS_PER_TICK IRremoteBoardDefs.h 50 Resolution of the raw input buffer data.

Handling unknown Protocols

Disclaimer

This library was never designed to handle long codes like the ones used by air conditioners. See Recording long Infrared Remote control signals with Arduino.
The main reason is, that it was designed to fit inside MCUs with relatively low levels of resources and was intended to work as a library together with other applications which also require some resources of the MCU to operate.

Hints

If you do not know which protocol your IR transmitter uses, you have several choices.

Other IR libraries

Here you find a short comparison matrix of 4 popular Arduino IR libraries.
Here you find an ESP8266/ESP32 version of IRremote with an impressive list of supported protocols.

Supported Boards

  • Arduino Uno / Mega / Leonardo / Duemilanove / Diecimila / LilyPad / Mini / Fio / Nano etc.
  • Teensy 1.0 / 1.0++ / 2.0 / 2++ / 3.0 / 3.1 / Teensy-LC; Credits: @PaulStoffregen (Teensy Team)
  • Sanguino
  • ATmega8, 48, 88, 168, 328
  • ATmega8535, 16, 32, 164, 324, 644, 1284,
  • ATmega64, 128
  • ATmega4809 (Nano every)
  • ATtiny84, 85
  • SAMD21 (receive only)
  • ESP32
  • ESP8266 is supported in a fork based on an old codebase that isn't as recent, but it works reasonably well given that perfectly timed sub millisecond interrupts are different on that chip. See https://github.com/markszabo/IRremoteESP8266
  • Sparkfun Pro Micro

We are open to suggestions for adding support to new boards, however we highly recommend you contact your supplier first and ask them to provide support from their side.

Hardware specifications

The timer and the pin usage can be adjusted in IRremoteBoardDefs.h

Board/CPU IR-Send (PWM) Pin Timers
ATtiny84 6 1
ATtiny85 > 1 MHz 1 0
ATmega8 9 1
ATmega48, ATmega88, ATmega168, ATmega328 3, 9 1, 2
ATmega1284 13, 14, 6 1, 2, 3
ATmega164, ATmega324, ATmega644 13, 14 1, 2
ATmega8535 ATmega16, ATmega32 13 1
ATmega64, ATmega128, ATmega1281, ATmega2561 13 1
ATmega8515, ATmega162 13 1
ATmega1280, ATmega2560 5, 6, 9, 11, 46 1, 2, 3, 4, 5
ATmega4809 5, 6, 9, 11, 46 TCB0
Leonardo (Atmega32u4) 5, 9, 13 1, 3, 4_HS
Zero (SAMD) *, 9 TC3
ESP32 4, all pins 1
Sparkfun Pro Micro 5, 9 1, 3
Teensy 1.0 17 1
Teensy 2.0 9, 10, 14 1, 3, 4_HS
Teensy++ 1.0 / 2.0 1, 16, 25 1, 2, 3
Teensy 3.0 / 3.1 5 CMT
Teensy-LC 16 TPM1

Revision History

Please see changelog.md.

API documentation

This project documents the library API using Doxygen. It is planned to make generated and up-to-date API documentation available online.

To generate the API documentation, Doxygen, as well as Graphviz should be installed. (Note that on Windows, it may be necessary to add the Graphviz binary directory (something like C:\Program Files\Graphviz2.38\bin) to the PATH variable manually.) With Doxygen and Graphviz installed, issue the command doxygen from the command line in the main project directory, which will generate the API documentation in HTML format. The just generated api-doc/index.html can now be opened in a browser.

Contributing

If you want to contribute to this project:

  • Report bugs and errors
  • Ask for enhancements
  • Create issues and pull requests
  • Tell other people about this library
  • Contribute new protocols

Check here for some guidelines.

Contact

Email: zetoslab@gmail.com Please only email me if it is more appropriate than creating an Issue / PR. I will not respond to requests for adding support for particular boards, unless of course you are the creator of the board and would like to cooperate on the project. I will also ignore any emails asking me to tell you how to implement your ideas. However, if you have a private inquiry that you would only apply to you and you would prefer it to be via email, by all means.

Contributors

Check here

Copyright

Copyright 2009-2012 Ken Shirriff Copyright (c) 2016 Rafi Khan